How to Replace a Bath Tub
How to Replace a Bath Tub
Blog Article
Presented here in the next paragraph you will find more good quality data all about How to Install a Bathtub.
Setting up a bathtub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is easily obtainable, the job can relocate rapidly; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have actually qualified on your own for the work as well as fit attempting it. Instead of working with a contractor to take over a halfway-completed project, it is much better to take into consideration using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will assist you mount a new bath tub in your restroom if you have actually already gotten a new bathtub and also don't require to change the plan of your previous water supply pipes.
Your devices and material list need to comprise the following:
Getting ready for the Setup
First of all, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, put the bathtub in the called for position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the tub until the level reads degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap connectors. The former type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall between the bathroom and also the tiling, leading to complications with dampness as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place a short review down below. We would be interested to listen to your suggestions about this blog posting. Hoping to see you back again soon. If you liked our post kindly be sure to pass it around. Many thanks for going through it.
Schedule Now! Report this page